Filters
Question type
Study Flashcards

Briefly describe the procedure recommended by Federal-Mogul Corporation for positioning the oil hole.

Correct Answer

verifed

verified

Install the bearings with their oil hole...

View Answer

After boring and honing, the top of the bore is chamfered about 1/16". Why is this done?

Correct Answer

verifed

verified

This is so that during install...

View Answer

____ occurs when the load on the engine is greater than the rpm needed to develop enough horsepower to pull the load.


A) Knurling
B) Lugging
C) Knocking
D) Stitching

Correct Answer

verifed

verified

Crosshatching that is too steep (less than 60 degrees) will allow oil to run down the cylinder wall; too flat (more than 20 degrees) causes too thick an oil film.

Correct Answer

verifed

verified

All of the following statements are true EXCEPT:


A) bearing clearance can be checked with Plastigage.
B) Plastigage is oil soluble and is readily cleaned from the bearing or crankshaft.
C) an engine with double oil clearance will throw off five times as much oil onto the cylinder walls, causing increased oil consumption.
D) you should rotate the crankshaft while Plastigage is in place.

Correct Answer

verifed

verified

Showing 21 - 25 of 25

Related Exams

Exam 1

Introduction to the Automobile

25 Questions

Exam 2

Automotive Careers and Technician Certification

25 Questions

Exam 3

Shop Safety

25 Questions

Exam 4

Shop Management, Service Records, and Parts

25 Questions

Exam 5

Locating Service Information and Specifications

25 Questions

Exam 6

Measuring Tools and Systems

25 Questions

Exam 7

Hardware, Fasteners, Drills, and Thread Repair

25 Questions

Exam 8

Shop Tools

25 Questions

Exam 9

General Shop Equipment

25 Questions

Exam 10

Cleaning Equipment and Methods

25 Questions

Exam 11

Lifting Equipment and Air Compressors

25 Questions

Exam 12

Engine Lubrication

25 Questions

Exam 13

Underhood and Body Inspection Vehicle on Ground

25 Questions

Exam 14

Undercar Inspection and Service

25 Questions

Exam 15

Introduction to the Engine

25 Questions

Exam 16

Engine Classifications and Types

25 Questions

Exam 17

Engine Size and Measurements

25 Questions

Exam 18

Engine Upper End

25 Questions

Exam 19

Engine Lower End and Lubrication System Theory

25 Questions

Exam 20

Cooling System Theory

25 Questions

Exam 21

Cooling System Service

25 Questions

Exam 22

Automotive Belts

25 Questions

Exam 23

Automotive Hoses

25 Questions

Exam 24

Automotive Plumbing: Tubing and Pipe

25 Questions

Exam 25

Basic Electrical System Theory and Repairs

25 Questions

Exam 26

Battery Fundamentals

25 Questions

Exam 27

Battery Service

25 Questions

Exam 28

Starting System Fundamentals

25 Questions

Exam 29

Starting System Service

25 Questions

Exam 30

Charging System Fundamentals

25 Questions

Exam 31

Charging System Service

25 Questions

Exam 32

Lighting and Wiring Fundamentals

25 Questions

Exam 33

Lighting and Wiring Service

25 Questions

Exam 34

Safety, Security, Comfort Systems, and Electrical Accessories

25 Questions

Exam 35

Heating and Air-Conditioning Fundamentals

25 Questions

Exam 36

Heating and Air-Conditioning Service

25 Questions

Exam 37

Ignition System Fundamentals

25 Questions

Exam 38

Ignition System Service

25 Questions

Exam 39

Petroleum Fuels and Alternative Fuel Technologies

25 Questions

Exam 40

Fuel System Fundamentals, Gasoline and Diesel

25 Questions

Exam 41

Fuel System Service

25 Questions

Exam 42

Intake and Exhaust Systemsturbochargers and Superchargers

25 Questions

Exam 43

Emission Control System Fundamentals, Gasoline and Diesel

25 Questions

Exam 44

Emission Control System Service

25 Questions

Exam 45

Electronics and Computer Systems Fundamentals

25 Questions

Exam 46

Electronics and Computer Systems Service

25 Questions

Exam 47

Advanced Emission and On-Board Diagnostics Obd

25 Questions

Exam 48

Diagnosing Engine Performance Problems

25 Questions

Exam 49

Diagnosing Engine Mechanical Problems

25 Questions

Exam 50

Engine Removal and Disassembly

25 Questions

Exam 51

Engine Sealing Gaskets, Fastener Torque

25 Questions

Exam 52

Engine Diagnosis and Service: Cylinder Head and Valve Train

25 Questions

Exam 54

Engine Diagnosis and Service: Piston, Piston Rings, Connecting Rod, Engine Balancing

25 Questions

Exam 55

Ordering Parts, Short and Long Blocks, Engine Assembly

25 Questions

Exam 56

Engine Installation, Break-In, and In-Chassis Repairs

25 Questions

Exam 57

Brake Fundamentals

25 Questions

Exam 58

Brake Service

25 Questions

Exam 59

Antilock Brakes, Traction, and Stability Control

25 Questions

Exam 60

Bearings, Seals, and Greases

25 Questions

Exam 61

Tire and Wheel Theory

25 Questions

Exam 62

Tire and Wheel Service

25 Questions

Exam 63

Suspension Fundamentals

25 Questions

Exam 64

Suspension System Service

25 Questions

Exam 65

Steering Fundamentals

25 Questions

Exam 66

Steering System Service

25 Questions

Exam 67

Wheel Alignment Fundamentals

25 Questions

Exam 68

Wheel Alignment Service

25 Questions

Exam 69

Clutch Fundamentals

25 Questions

Exam 70

Clutch Diagnosis and Service

25 Questions

Exam 71

Manual Transmission Fundamentals

25 Questions

Exam 72

Manual Transmission Diagnosis and Repair

25 Questions

Exam 73

Automatic Transmission Fundamentals

25 Questions

Exam 74

Automatic Transmission Diagnosis and Service

25 Questions

Exam 75

Driveline Operation

25 Questions

Exam 76

Driveline Diagnosis and Service

25 Questions

Exam 77

Front-Wheel-Drive Transaxle and Cv Joint Service

25 Questions

Exam 78

Front-Wheel-Drive Transaxle and Cv Joint Service

25 Questions

Exam 79

Driveline Vibration and Service

25 Questions

Exam 80

Hybrid Electric Vehicle Fundamentals

25 Questions

Exam 81

Hybrid Vehicle Safety and Service

25 Questions

Exam 82

New Vehicle Technologies: Battery Electric, Fuel Cell Electric, and Hydraulic Hybrid

25 Questions

Show Answer