Question 1

What is the universal symbol for section lining?

Accepted Answer

A)   perpendicular lines
B)   crosshatching
C)   solid fill
D)   an "S" inside a circle

Question 2

Imagine that the sectional details for a part you are drawing are too small to be interpreted and dimensioned. What should you do?

Accepted Answer

A)   prepare auxiliary sections
B)   prepare enlarged sections
C)   eliminate very small details to simplify the drawing
D)   prepare the sections as clearly as possible and add notations to explain details that are too small to be drawn

Question 3

Where should notes and dimensions be placed when using section lining?

Accepted Answer

A)   on a separate page
B)   inside of the view
C)   outside of the view
D)   wherever there is adequate space

Question 4

A cutting plane typically extends through an object in a straight line.

Accepted Answer

A) True 
 B)False

Question 5

Sectional views are used to show the size and shape of the exterior of an object.

Accepted Answer

A) True 
 B)False  False

Question 6

Imagine that you have used the universal crosshatching symbol rather than the standard material section-lining symbol on a drawing. What should you do?

Accepted Answer

A)   start over with a new drawing
B)   place a note near the section to indicate the type of material
C)   remove the crosshatching and replace it with the standard material section-lining symbol
D)   nothing-the use of the universal crosshatching symbol is appropriate by itself and requires no further action or notation

Question 7

Imagine that you are drawing an object that includes a spoked wheel that does not align with the cutting plane. What should you do when projecting the sectional view?

Accepted Answer

A)   rotate the object and section line the spoke
B)   rotate the object and refrain from section lining the spoke
C)   draw the projection using straight line separations
D)   draw the projection without any modification

Question 8

In architectural drawings, a full-section top view is called a _____ view

Accepted Answer

A)   vertical
B)   sectional
C)   profile
D)   plan

Question 9

Cutting plane lines are:

Accepted Answer

A)   thin with an arrow on one end
B)   wide with an arrow on one end
C)   thin with arrows on each end
D)   wide with arrows on each end

Question 10

Auxiliary sections should be aligned perpendicular to the projection lines of the auxiliary views.

Accepted Answer

A) True 
 B)False

Question 11

When are half-sections used?

Accepted Answer

A)   when the object is symmetrical
B)   when the object is circular or tubular
C)   when the object has holes
D)   when the object has protrusions A

Question 12

What type of section is used when only a small part of an object needs to be sectioned?

Accepted Answer

A)   half-section
B)   broken-out section
C)   offset section
D)   full section

Question 13

Materials that are too thin to section with crosshatching are sectioned as outlined shapes without any type of fill.

Accepted Answer

A) True 
 B)False

Question 14

When offsetting cutting plane lines, you should always:

Accepted Answer

A)   bend the line at right angles to the cutting plane and perpendicular to the plane of projection
B)   maintain straight lines that run parallel to the plane of projection
C)   show any bends in the cutting plane in the sectioned view
D)   omit special features such as a countersunk hole or a slot A

Question 15

Imagine that you need to draw a broken-out section for an object. How should you indicate the separation of the sectioned area from the remainder of the drawing?

Accepted Answer

A)   with two straight lines that form a 90° angle
B)   with two straight lines that form a 45° angle
C)   with an irregular short break line
D)   with a semicircular long break line

Question 16

Which of these should be section lined?

Accepted Answer

A)   curved surfaces
B)   spokes
C)   ball bearings
D)   gear teeth

Question 17

Where the cutting plane passes through solid material, _____ lines are drawn.

Accepted Answer

A)   half-section
B)   assembly
C)   section-lining
D)   cutting plane

Question 18

Nuts and bolts should not be section lined.

Accepted Answer

A) True 
 B)False

Question 19

To define the location of the imaginary sectional plane, a(n)  _____ is drawn on the view where the cut was made.

Accepted Answer

A)   cutting plane line
B)   crosshatch
C)   thin wall line
D)   offset line

Question 20

The spacing of crosshatching lines:

Accepted Answer

A)   should be 1/16"
B)   should be 1/8"
C)   should be 1/4"
D)   will vary depending on the size of the section

Exam 11: Sectional Views

What is the universal symbol for section lining?

Correct AnswerverifiedShow Answer

Imagine that the sectional details for a part you are drawing are too small to be interpreted and dimensioned. What should you do?

Correct AnswerverifiedShow Answer

Where should notes and dimensions be placed when using section lining?

Correct AnswerverifiedShow Answer

A cutting plane typically extends through an object in a straight line.

Correct AnswerverifiedShow Answer

Sectional views are used to show the size and shape of the exterior of an object.

Correct AnswerverifiedFalse

Imagine that you have used the universal crosshatching symbol rather than the standard material section-lining symbol on a drawing. What should you do?

Correct AnswerverifiedShow Answer

Imagine that you are drawing an object that includes a spoked wheel that does not align with the cutting plane. What should you do when projecting the sectional view?

Correct AnswerverifiedShow Answer

In architectural drawings, a full-section top view is called a _____ view

Correct AnswerverifiedShow Answer

Cutting plane lines are:

Correct AnswerverifiedShow Answer

Auxiliary sections should be aligned perpendicular to the projection lines of the auxiliary views.

Correct AnswerverifiedShow Answer

When are half-sections used?

Correct AnswerverifiedA

What type of section is used when only a small part of an object needs to be sectioned?

Correct AnswerverifiedShow Answer

Materials that are too thin to section with crosshatching are sectioned as outlined shapes without any type of fill.

Correct AnswerverifiedShow Answer

When offsetting cutting plane lines, you should always:

Correct AnswerverifiedA

Imagine that you need to draw a broken-out section for an object. How should you indicate the separation of the sectioned area from the remainder of the drawing?

Correct AnswerverifiedShow Answer

Which of these should be section lined?

Correct AnswerverifiedShow Answer

Where the cutting plane passes through solid material, _____ lines are drawn.

Correct AnswerverifiedShow Answer

Nuts and bolts should not be section lined.

Correct AnswerverifiedShow Answer

To define the location of the imaginary sectional plane, a(n) _____ is drawn on the view where the cut was made.

Correct AnswerverifiedShow Answer

The spacing of crosshatching lines:

Correct AnswerverifiedShow Answer

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
False

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
A

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
A

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified