Filters
Question type

In what MY did single actuator EUIs cease to be used on any North American, Highway certified diesel engine?


A) 1997
B) 2003
C) 2007
D) 2010

Correct Answer

verifed

verified

Besides identifying a dead cylinder, what else can a multi-cylinder cutout test identify after performing a cylinder cutout test?


A) emissions analysis
B) cold engine operation
C) unbalanced cylinder fueling
D) all of the above

Correct Answer

verifed

verified

What type of transfer pump is used in the fuel sub-system in most EUI-fueled engines?


A) fixed clearance gear pump
B) helical gear pump
C) plunger pump
D) vane type pump

Correct Answer

verifed

verified

What pressure is used to charge Cummins CELECT Plus injectors?


A) they are under suction
B) 78 psi
C) 150 psi
D) 285 psi

Correct Answer

verifed

verified

What does the injector response time (IRT) allow DDEC electronics to do when managing EUI pulse width?


A) compensate for minor EUI circuit resistances
B) adjust for EUI mechanical wear
C) compensate for a failed EUI control cartridge
D) adjust EUI firing sequence

Correct Answer

verifed

verified

What force is used to convert charging pressures into injection pressures in EUIs?


A) electronic from control cartridge
B) electrical from injector drivers
C) hydraulic from fuel sub-system
D) mechanical from injector cam profile

Correct Answer

verifed

verified

Which domestic engine manufacturers of onhighway commercial diesel engines are using single-actuator EUIs after the EPA 2007 model year?


A) DDC only
B) Volvo-Mack only
C) Caterpillar only
D) None

Correct Answer

verifed

verified

What does the control cartridge mechanically move to manage an effective stroke in a single-actuator EUI?


A) pumping plunger
B) barrel
C) nozzle needle
D) poppet control valve

Correct Answer

verifed

verified

Which of the following terms used by DDC to describe DDEC EUI fueling has the same meaning as split shot injection?


A) pilot injection
B) detonation
C) quiescent combustion
D) maximizing injection pressure

Correct Answer

verifed

verified

What electronic component houses the electronic distributor unit (EDU) in versions of DDEC fueled engines manufactured before 2007?


A) ECM
B) PCM
C) MCM
D) CPC

Correct Answer

verifed

verified

When the control cartridge is energized in a typical single actuator EUI, which of the following passages is immediately closed off?


A) cylinder head return gallery
B) EUI pump chamber to nozzle duct
C) nozzle valve pressure chamber
D) EUI control valve spill

Correct Answer

verifed

verified

When a typical EUI is managing pilot injection, when should the second pulse begin?


A) at 15 degrees ATDC
B) the moment the pilot pulse ignites
C) peak cylinder pressure
D) during afterburn

Correct Answer

verifed

verified

B

How is EUI duty cycle usually displayed on electronic service tools (ESTs) ?


A) crank angle degrees
B) pulse width (PW)
C) on-off duration
D) cubic mm of fuel pumped

Correct Answer

verifed

verified

Which of the following must happen to enable an EUI to no-fuel, and therefore shutdown, an engine?


A) EUI solenoid not be energized
B) no plunger stroke
C) camshaft does not ramp off IBC
D) camshaft ceases to rotate

Correct Answer

verifed

verified

A

If an injector calibration code is inscribed as A, B, or C, what is the likely engine application of the EUI?


A) 1st generation DDEC
B) Late generation DDEC
C) 1st generation Volvo
D) Late generation Caterpillar

Correct Answer

verifed

verified

When a four-cylinder cutout test is being performed on an engine, what is the minimum number of cylinders that should be firing during the test cycles if all the EUIs are functioning properly?


A) One cylinder
B) Two cylinders
C) Four cylinders
D) Six cylinders

Correct Answer

verifed

verified

What voltage are Cummins CELECT EUIs switched at?


A) 5 V-DC
B) 12 V-DC
C) 78 V-DC
D) 100 V-DC

Correct Answer

verifed

verified

C

Where do Caterpillar usually locate a hand priming pump in their EUI-fueled engine?


A) on the secondary filter housing
B) at the fuel tank pick-up tube
C) at the gear pump inlet
D) on the primary filter housing

Correct Answer

verifed

verified

Technician A says that to program EUI fuel flow rates to an ECM, some engines require a new engine file to be downloaded from the OEM data huB. echnician B says that failure to reprogram the calibration code on injector change-out is unlikely to cause any harm providing the engine runs smooth at idle after start-up. Who is correct?


A) Technician A only
B) Technician B only
C) Both A and B
D) Neither A nor B

Correct Answer

verifed

verified

When Caterpillar single actuator MEUIs are energized by the ECM drivers, voltage peaks at:


A) 5 V-DC
B) 8 V-DC
C) 12 V-DC
D) over 100 V-DC

Correct Answer

verifed

verified

Showing 1 - 20 of 42

Related Exams

Show Answer